In my new book, Old Windows Made Easy, I outline the complete process for restoring wood windows. Today, I want to walk you through some of the content in the book for free right here and teach you how to remove window sash.
If you want to learn more about restoring your wood windows, you can Order Your Copy Now!
Step 1 Remove the Stop
The first thing you need to do in order to restore or repair your double-hung windows is get the sash out of the jamb. Depending on how much built up paint and caulk there is, this may be simple or difficult. Get both the bottom and top sash out before moving onto anything else.
The first piece to remove is the stop. This is a small piece of trim that is usually nailed in place along the side of the jamb. Some stops are screwed in place, which will have to be unscrewed and then gently pried off. You want to avoid breaking the stops since it can be hard to find matching profiles today, though if they do break, they can be replaced with stock moldings available to most lumber yards or home stores.
The window stop was designed to be removed to service the window, so don’t worry that you are doing something wrong by prying this piece off. What makes it difficult is usually decades of excess paint or unnecessary extra nails by an overzealous handyman.
To get your sash out, you only need to remove the stop on one side, but you can remove both if you want to clean them up more thoroughly.
- Gently score the paint between the stop and, the jamb and the stool and the sash with a razor knife being careful not to gouge the wood. Don’t cut too deeply, just enough to cut through the paint bond.
- Using a trim pry bar or firm putty knife, gently pry the stop away from the jamb. Some stops will be installed using screws and washers instead of finish nails. These must be unscrewed.
- Remove any remaining nails from the stop with a nail puller by pulling them through the back side of the stop.
- Scrape the backside of the stop that runs against the sash with a carbide scraper to clean away any built up paint or caulk.
- Number the back of the stop to go with the corresponding window and set aside for reinstallation later.
- Pull any remaining nails that may be left in the jamb.
Step 2 Remove Bottom Sash
The bottom sash is the most inside sash and so it must be removed first before you can gain access to the top sash. The bottom sash is usually much easier to remove than the top sash so it’s the place to start.
While you can cut the paint free on the exterior, it’s usually easiest to simply focus on the interior when it comes to the bottom sash and let the majority of the exterior paint buildup break off as you remove the sash.
If your bottom sash is not painted shut, then that eliminates all this cutting of paint and caulk and it is that much easier to remove.
- Cut the paint seal between the bottom sash and the remaining stop and possibly between the bottom sash and stool if necessary.
- Insert a firm putty knife in between the meeting rails and gently pry the sash loose to break the paint seal. Lift the sash above the stool to remove it.
- Swing the side of the lower sash where the interior stop was removed inward to access the rope mortise on the side of the sash.
- Remove the knotted rope from the rope mortise, being careful not to let the sash drop or the rope (which is attached to the hidden weights) fly out of your grasp. Sometimes the rope may be nailed into the side of the sash. This nail will require removal in order to get the knot out.
- Gently allow the rope knot to rest against the pulley. If the knot isn’t big enough to keep the rope from falling back into the pocket, tie a larger knot.
- Repeat the process on the other side of the bottom sash.
- If you are doing multiple windows, number the sash on the side so that it can be reinstalled into the proper window later.
- Scrape, slice or sand away unnecessary paint buildup on sash that may prevent movement.
Step 3 Remove Parting Bead
Step 3 and 4 are pretty much done at the same time because the easiest way to remove the parting bead is to have the top sash lowered all the way to the sill. So, that means cutting it free of paint and caulk.
The parting bead may be painted and caulked so much that it looks like it should not be removed, but it is a separate piece that was designed to be removed in order to remove the top sash.
Parting bead can be eternally frustrating, but duck-billed vise grips are its nemesis. Some parting bead will be nailed in place and others will be simply pressure fit. Either way requires the parting bead to be pulled straight out of the channel it rests in and then removed (often in pieces).
- Cut parting bead free of paint or caulk at top sash using a razor knife or window zipper.
- Work the sash up and down until you can lower it all the way down to the sill.
- Starting at the top and working your way down, use duck billed vise grips to grasp the parting bead and wiggle it back and forth to work it loose.
- Cut and fit new parting beads if necessary.
- Scrape excess paint from parting beads.
- Prep parting beads for paint and reinstallation.
Step 4 Remove Top Sash
Ah, the top sash. Most people don’t believe that this part of the window ever moved, but on double-hung windows, they are most definitely mistaken. There are single-hung windows where the top sash is stationary and will not move so before you get too deeply into this work make sure that your windows are not single-hung.
Top sashes are usually so gummed up that they are almost impossible to move without major effort. When cut free of paint, the top sash will move all the way down to the sill, but getting it there is a challenge. If you have serious paint building up and the sash barely budges, keep working it up and down to try to gain as much motion as possible.
If the top sash absolutely won’t go down to the sill, it can still come out as long as you can have it lowered enough to reveal the pulleys. If the pulley is revealed and your parting bead is out, go ahead and try to swing the side out and remove the sash from the jamb.
- Cut all paint seals around top sash with a razor knife or window zipper. The window zipper is good because it has little files that sand away the paint buildup in the paint joint once the paint seal is broken.
- Move the top sash all the way down to the window sill. If the sash will not move due to paint build up, you can continue, but the parting bead will be more difficult to remove and will likely come out in pieces.
- After the parting bead is out of one side, swing that side of the sash inward and remove the ropes as with the bottom sash.
- Be sure to number the sash.
- Scrape, slice or sand away unnecessary paint buildup on blind stop and jamb that may prevent smooth movement of the sash.
That’s it! You’ve now removed your sashes and can work on them at your leisure and put them right back in the jamb whenever you are ready. Make sure you have some plywood cut to size to cover the opening or a storm window in case you plan to keep them pout for a longer time to do your work.
If you found this helpful, you’ll definitely want to order your copy of Old Windows Made Easy. There are a lot more tutorials just like this to help you work your way through the restoration of your old windows.
Founder & Editor-in-Chief
I love old houses, working with my hands, and teaching others the excitment of doing it yourself! Everything is teachable if you only give it the chance.