fbpx bloglovinBloglovin iconCombined ShapeCreated with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. rssRSS iconsoundcloudSoundCloud iconFill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. SearchCreated with Lunacy Search iconCreated with Sketch.

How To: Install Spring Bronze Weatherstripping

Spring Bronze weatherstripping

To allay your concerns that old doors and old windows can’t be energy-efficient, I wanted to make sure we covered how to install weatherstripping on these openings.

Weatherstripping has changed a lot over the years. Today it is usually foam, vinyl, or felt peel and stick weatherstripping, but there is an old school way of weatherstripping that will last well over 100 years and be just as effective, if not more, than today’s methods.

Spring bronze weatherstripping, while a bit more work than the peel and stick variety, provides an excellent seal to keep air, water and bugs out of your home. Bronze weatherstripping is extremely effective and durable enough to last generations.

There are several types of metal weather stripping. Some are more complicated than others and require modifications to the doors or windows. Leave those to the pros. For the average homeowner, spring bronze weatherstripping will be just as effective and it is user-friendly to install.

Buy your spring bronze right here!

Here’s how to install it:

Tools Needed
 

Step #1 Cut to Size

how to cut spring bronze

Measure the door openings and using tin snips cut the weatherstripping to length. The weatherstrip needs to go in the rabbet that the door fits into when closed. There is a flat side and sprung side to spring bronze. The flat side goes on the interior and the sprung side faces the exterior so that the door compacts it as it closes.

You’ll need to cut the bronze so that it doesn’t cover and interfere with the hinges or latches.

Nail spring bronzeStep #2 Nail in Place

Line up your spring bronze and nail it in from the top down. Make sure you start from one end and keep the bronze straight the whole length so it does not bubble or bind in places. Also, be careful not to nail the bronze too close the the door jamb (see spacing in photo) or it may not be able to lay down completely when compressed.

Your nails should be no more than 2” apart. I prefer 1 1/2” between nails to make sure the installation is lasting.

Corners require the weatherstripping to meet at simple butt joints.

The nails should be flush with the surface. Run your fingers across them and if you feel any that are standing a bit proud, set them a bit more with a nail set.

spring bronze finished installationStep #3 Spring the Bronze

Depending on how tight the existing door is in the frame, you may need to increase the spring angle on the weatherstripping.

Use a putty knife or screwdriver to gently bend the bronze to increase the tightness of the fit. Close the door and check for any gaps where you can see sunlight. If you do, open the door and bend the bronze a bit more in that section until you achieve a good seal.

Spring bronze is an excellent material for weatherstripping. Installed properly, it will never need replacing and is extremely flexible to fit almost any size gap around doors and windows.

Subscribe Now For Your FREE eBook!

97 thoughts on “How To: Install Spring Bronze Weatherstripping

  1. Hello-
    Can I use this on old double hung windows? we are redoing our old windows and looking to make them more energy efficient.
    Thanks
    Old house in Charleston, SC

  2. I saw a tutorial on another site where the installer installs the hinge side spring bronze with the nailing strip close to the rabbet. he does not cut around the hinges. The bronze lays against the hinges when the door closes. Would you say this is an acceptable alternative to the other method leaving the hinges open so air drafts around them?

  3. What width of bronze should I use on my windows? I built some windows for a porch that are 3/4” thick but I’m having trouble finding bronze of that size. Is it okay if it’s a little wider?

  4. I have single hung windows. Should I install spring bronze on the upper sash also? I am finding very little information about old single hung window restoration. Most of the double hung information applies but I wondered if the stationary sash should be sealed differently.

  5. I’ve put in bronze weatherstrip on a number of doors, and I find it imperative to pre-drill nail holes (1/16″ bit) in the bronze weatherstrip before nailing. I usually space my nails about 2″ apart and use a small 10 oz hammer. I start with a nail on one of the strip and a second nail about half the way down. The placement of the WS before the second nail is placed is most important. It determines where the WS will lie, without binding, along its whole length. You should not try to adjust the position of the strip after the second nail is placed. Remove the second nail and reposition the WS. Check for position before driving the second nail home.
    Once in a while the angle running along the length of the WS is not enough. If so, cut the piece to length and, along the length, clamp it between two straight boards at the bend and gently bend to achieve a greater angle.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.