fbpx bloglovinBloglovin iconCombined ShapeCreated with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. rssRSS iconsoundcloudSoundCloud iconFill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. Fill 1Created with Sketch. SearchCreated with Lunacy Search iconCreated with Sketch.

How To: Glaze Wood Windows

Bed glass

Continuing our focus on window restoration to mark the release of my new book Old Windows Made Easy, I decided to post about putty glazing today. This skill is one of the most important and difficult to get right. Proper glazing makes for long lasting, well-sealed windows.

The good news is that it doesn’t need to be perfect, just done well enough so that it sheds water and seals the glass properly. The nice thing about putty glazing is that if you don’t like the results the first time, you can scrape it off and try, try again until you’re satisfied.

The following is almost an exact excerpt from the book. If you want the complete step-by-step guide for restoring your wood windows, get your copy of Old Windows Made Easy.

How To Glaze Wood Windows

Old wood windows traditionally have glazing putty on the exterior of the sashes. This beveled putty glazing is the big finish to all the restoration work and is typically the last thing done before finish painting.

You can work the putty until you are satisfied with the results. A well glazed window should have clean straight lines of putty and none of it should be visible to occupants from the inside.

Step #1 Bed Glass

Bedding the glass refers to installing the glass back into the sash in a bed of putty. This helps air seal the glass and prevents water from getting behind the glass due to condensation.

Insert the glass into the opening gently and apply firm pressure around the edges. This will cause excess putty to squeeze out the inside.

Once you have the glass, in insert your glazing points (I prefer the diamond points because they are easier to hide behind the putty line). Make sure they are firmly in place and the glass is where you want it to be before setting your points.

Make sure the glass is evenly set into the puttied glazing rabbet and you only leave a thin film of putty on the interior side of the glass.

Action Steps
  1. Dry fit glass into sash to determine the correct orientation. Trim glass if needed.
  2. Bed a small amount of Sarco Type-M (or similar) putty in glazing rabbets and gently press glass into bedding. Only press the glass around the edges, especially on large pieces. Pressing on the center of the glass can stress it too much and cause it to break.
  3. Use a point driver or putty knife to insert at least one glazing point into each side of glass and an additional point every 12″. (Be sure to set point far enough back so that it lays behind the glazing rabbet.)
  4. Remove excess putty from inside of sash and tool interior putty flush and smooth with profile.

Step #2 Finish Glaze

Properly installed finish glazing putty should be installed at a 45° angle with mitered corners to allow it to shed water effectively. I won’t lie that this can take some practice to get just right. But perfectly glazed windows are not necessary for the putty to do its work.

When you first get your putty out, mix it thoroughly to ensure the oils are spread throughout the whole batch of putty. If the putty is cold, you can knead it a bit to help it gain some workability. My preferred putty is Sarco MultiGlaze but other forms are acceptable like DAP 33 which is readily available at most hardware stores.

In #5 below I mention using whiting. This is simply ground up chalk and it helps to absorb excess oils from the putty and clean the oil residue that inevitably gets on the glass. You can usually find it at paint stores or online.

Action Steps
  1. Place putty into glazing rabbet.
  2. Pack putty firmly in the glazing rabbet and glass junction to get a good seal.
  3. Using a putty knife tool, finish glazing at a 45° angle to smooth finish with clean mitered corners.
  4. Remove excess putty.
  5. Using an old paint brush, apply whiting to inside and outside of glass. Work in thoroughly to remove oil spots from glass being careful not to disturb putty. Blow off remaining whiting.
The end result with clean crisp lines and corners
The end result with clean crisp lines and corners

Once your windows have been glazed, the putty will need some time to skin over before painting. Some putties require weeks before being ready for paint while others require only a few hours.

It depends on the putty and the paint type. Always check the manufacturer’s recommendations for the putty you are using and keep in mind that weather conditions will also cause curing time to vary.

One last note: ALWAYS paint your putty! Putty will last for decades if kept properly painted. If not painted, you only have a few months before mildew and dried out putty will make you start all over again.

If you liked this you can also view my video on gazing wood windows at How To: Reglaze Your Old Windows (Video Tutorial).

Subscribe Now For Your FREE eBook!

10 thoughts on “How To: Glaze Wood Windows

  1. My front door, that is covered by patio-no weather elements is raw wood, with some oil or finish on it for a nice color-I dont believe there is urethane or anything. I put new glazing putty per your instructions-thank you…..but, the putty is obviously white, my wood is brown, is it common to paint the putty to match the wood?

  2. Hi, need help, my house windows are about 10years old recently moved into the property and it’s come cold with drafts through the glass it’s self. Notice that some of the putty has turned black an coming off in bits. Would this be an easy job for a novice to repair or would it be best to get new windows fitted? Sorry for long message but I’m looking into restoring my kitchen rather then buy new.

  3. Hi Scott,

    Glazing info has been a huge help. I’m chipping away at 32 windows in a 1928 Craftsman that my wife and I bought a little over two years ago. NONE were originally bedded with glazing putty. I do gave a question that is not not-precisely window related.. We have some beautiful old doors with 15 lites each that use wood glazing strips. I swore that you had a post about how to properly handle them but can’t find it. Do they also require glazing putty to bed them?

    1. You plan to stain the exterior of the Windows? If that’s so then be sure to cover the putty with a spar urethane along with the rest of the sash. If the putty is left bare it will mildew and fail in fairly short order.

        1. Question for Beth: Did you ever buy the house? If so, how’d the windows turn out? I would think that replacing the glazing with wooden strips might be a good option for a situation like yours, but I’m interested in your results. Thanks!

      1. How long should I wait after putting putty (Dap 33) in to apply next coat of stain and varnish OVER the putty? Could not remove windows. Had to spot putty inside. Sash and frame are all wood. I stripped, sanded,stained, urethaned, waited for Urethane to dry, applied Boiled Linseed Oil to sash and puttied.

  4. hi scott,
    Is it possible to reglaze window without taking them apart just to replace broken panes 26×26? I’m more worried about the outside elements for the curing time, before painting. any suggestions?

  5. Very sensitive work, but it doesn’t really required to be perfect, because you can do it with your own satisfaction and acceptable results. Just follow these few steps and you will be happy with your work.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.